• For FS-I6 FS-T6 FS-Ct6b FS-T4b Fs-i4;line data cable connection to download the firmware upgrade applies;Suitable for transmitter and computer connection,.
• The FlySky FS-SM600 6CH USB Controller makes it super simple to hook up a lifelike radio controller to your favorite RC Simulator. You only need to connect it to your computer, no other power source is needed.

1. Flysky Transmitter Problems
2. Flysky Transmitter Software Download
3. Flysky Drivers And Software

How to install and get the PC software working for an Exceed FS-CT6B Transmitter. Turborix, Exceed are re-branded Flysky Transmitters so this install page.

Before you can jump into setting up the software on your new racing drone, you are going to have to configure your transmitter to communicate with your receiver. If you launch Betaflight / Cleanflight / etc. without configuring your transmitter, it will be impossible to set everything up. Furthermore, if you want to use switches or other auxiliary inputs to manage your flight modes or arm and disarm your quad, you will need to set those features up on the transmitter first.

Flysky Transmitter Problems

For the most part, you will want to focus on three things primarily for a basic setup. Obviously there are many, many more features that you can configure (and we listed a few at the end of this article), but we are going to focus on the key features that will get you in the air:

• Bind your transmitter to your receiver.
• Setup any auxiliary switches on the transmitter.
• Ensure that your failsafe is configured correctly.

If you setup these three items correctly, you can complete the software setup for your quadcopter. While we would also recommend reviewing more advanced features, such as setting up telemetry information and battery alarms, it is not imperative for getting into the air.

We plan to delve deeper into settings features and provide a highly detailed setup article in the future. For the time being, we have compiled a ton of community resources that can be used to complete most of the setup steps.

For most setups, you will create a new quadcopter model on your transmitter and bind that model with your receiver. However, be sure to read the manual for your receiver before engaging any bind mode. Some receivers will be very specific on how you should bind the receiver and transmitter together. Failure to take the time here to bind the two correctly can result in a lot of headaches later when trying to configure advanced features.

Taranis setting up a model + binding information (Rotor Riot)

Taranis binding using D4R-II (HeliBaticsTV)

Flysky Transmitter Software Download

Spektrum Binding Satellite for Cleanflight and Betaflight

FlySky i6 / Turnigy i6 Setup and Binding Guide

RadioLink AT9 initial binding – Vortex quad example

For most setups, you will have to setup the auxiliary switches on your transmitter before they will register in the flight controller software. This is commonly configured in a “mixer” setting (Taranis), where you will add additional inputs alongside your default throttle, yaw, pitch, and roll.

Setting up auxiliary switches – Taranis (Rotor Riot)

Taranis auxiliary switch setup (UAVFutures)

DX-6i Mode Switch Setup

FlySky i6 / Turnigy i6 Flight Mode Switch Setup

Changing channels / switches with Radiolink AT9

This is more of a fringe issue that shouldn’t be a problem with most setups. More often than not, if you run a failsafe test and are unable to get a failsafe throttle signal after disconnecting your transmitter, it is likely an issue with your binding process. Here are a few threads and videos that may help with the issue. We have personally seen this when (incorrectly) binding a FrSky D4R-II to a Taranis.

Flysky Drivers And Software

Failsafe and disarm test (Joshua Bardwell)

Failsafe setup incorrectly fix

Relevant Thread: RCGroups thread on correct D4R-II setup and binding

FlySky i6 / Turnigy i6 Failsafe Setup

Radiolink AT9 failsafe setup

You can also configure some other neat bells and whistles on your transmitter. Having a battery alarm when your cells are getting low, live telemetry info, and other configurable elements can be extremely valuable when flying. We plan to expand on this in greater detail in the future.

Taranis introductory to telemetry and alarms (Painless360)

Now that your transmitter is configured and talking to your receiver, you can complete your software setup. Continue on to Novuh’s three part article on software setup here.

FlyHelp is a shareware, so you can download it and try it before you buy it. This download is the fully-functional version of the application and includes all features.

If you have already purchased a license, you can use your key to disable trial mode.Tiki navigator serial key generator free.

FlyHelp require the Micirosoft .NET Framework 4.0 to be installed. If it isn't already installed in your computer, just follow the link below.